Your Complete Instruction for Installing a Bathtub
Your Complete Instruction for Installing a Bathtub
Blog Article
This great article which follows pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is highly informative. Read it for your own benefit and figure out what you think about it.
Installing a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging project. If the old tub is readily easily accessible, the project can move immediately; if you have to open a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly need a helper to move out the old tub as well as embeded in the new one. Make sure you have qualified on your own for the job as well as are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed task, it is far better to think about employing one before you begin. Possibilities are you may require a professional plumber to make tube links.
This post will certainly assist you install a new bathtub in your shower room if you have actually already gotten a new bathtub as well as do not need to alter the plan of your previous water supply pipes.
Your devices and also material checklist should comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly originate from the pipelines. Once the supply pipelines have been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Safeguard the faucet in position with the maker given backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former kind ought to be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the required placement. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the tub until the spirit level reads level.
To install taps, fit all-time low of the furthest versatile tap adapter to the ideal supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Activate the water and examine all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Finally, fix the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub ought to wait until the bathtub has been used at least when as this will certainly settle it right into its final position.
Planning for the Setup
Firstly, the supporting framework provided with the bathroom must be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop strain on the tub.
Fit the adaptable tap connectors to the bottom of the two taps using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, creating the water to permeate the wall between the bathroom and the tiling, resulting in problems with moisture and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and also installations. They are sold in tubes and also cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to allow for the movement experienced when the bathtub is in usage. The sealer can fracture relatively early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the market. It is a good idea to fit the tiles utilizing water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on Tools You Need to Install a New Bathtub ? Write feedback directly below. We would be delighted to listen to your ideas about this write-up. We are looking forward that you visit us again later on. Enjoyed our write up? Please share it. Help others locate it. We treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
Rely on our emergency expertise. Report this page